Page 329 - CATALOG

GILDERS PASTE

Use Gilders Paste ™ on:
African Antique Apricot Black Picture Frames, Etched Glass, Furniture, Antique Restoration,
Bronze Gold CS303PP-AP CS303PP-BLK
(Metallic) (Metallic) Finials, Crafts, Embossed Molding, Miter Joints, Ornate Fretwork,
CS303PP-AB CS303PP-AG Rope & Dental, Chair Railing, Curtain Rods, Ceramics, Gilding Res-
toration, Bisque Ware, Plaster, Home Décor Stenciling,
Gessoed Surfaces, Stone, Paper, Wax, Leather, Textiles, Plastics,
previously painted or any clean, dry surface.
Bronze Canary Celtic Copper
(Metallic) Yellow Bronze (Metallic)
CS303PP-BZ CS303PP-CY (Metallic) CS303PP-CU SUGGESTIONS
CS303PP-CB Substrate surface should be dry and clean, free of dirt, oil,
grease and scale.
Coral Cream Damson Foundry Gilders Paste™ can be directly applied with your finger,
Red CS303PP-CM (Deep Purple) Bronze sponge, paint - tooth - stencil brushes, cloth, rubber
CS303PP-CR CS303PP-DAM (Metallic)
CS303PP-FB stamps etc… All colors can be thinned out to further
extend, wash, stain or paint your project.
Blending Gilders Paste™ is as easy as mixing two or more
German Gold Inca Iris
Silver (Metallic) Gold Blue col ors to match and touch up existing color schemes or to
(Metallic) CS303PP-G (Metallic) CS303PP-IB cre ate a custom color.
CS303PP-GS CS303PP-IG
Drying time varies depending on materials, thickness of
application and substrate, approximately 30 - 60 minutes
Orange Pantina Pinotage Rich to the touch on dry, low porosity, debris free surfaces.
CS303PP-O CS303PP-PT CS303PP-PO Gold
(Metallic) Lightly polishing metallic colors with a soft cloth, after
CS303PP-RG 12 hours of drying, will produce a gilded finish.
Will accept an overcoat, such as UV solvent based stable
Rust Sandalwood Silver Slate clear lacquer, varnish, acrylic, or clear powder coating to
CS303PP-RUST CS303PP-SW (Metallic) CS303PP-SL achieve a uniform appearance where the Gilders Paste™
CS303PP-S
was not used, or, to provide increased durability to areas
where repeated.

Tulip Verdigris Violet White TIPS & TECHNIQUES
Red CS303PP-V CS303PP-VL CS303PP-W For very smooth surfaces, such as gloss paint, plastic,
CS303PP-TR
ceramics and furniture, it is recommended to abrade the
surfaces with 0000 grade steel wool or fine sandpaper or
apply a rec ommended primer. PAINT & PATINAS
(Colors may vary slightly from printed medium)
Layering substrates with a solid base color and then
Small, 30 ml (1 oz.), covers over 30 sq. ft.
stencil ing, sponging or wiping another color over base
coat can produce unique affects and blends.
Polishing the base coat immediately after application
with a dry cloth or slightly wetting it with a thinner will
remove Gilders Paste™ from the relief detail and highlight
depressed details. Lightly brushing Gilders Paste™ over the
top will highlight the relief details without polishing.

Store above 55˚F. Apply above 60˚F. If Gilders Paste™
becomes dry, add a little paint thinner or mineral spirits,
mix, and you are ready to go.
WARNING:
COMBUSTIBLE. Do not store or use near open flame. KEEP OUT OF REACH OF CHILDREN. NOT FOR USE IN HEALTH CARE FACILITIES. For further
health information contact a poison control center. Use in well ventilated area. Request a materials safety data sheet when using in man ufacturing. Keep in
the original container with the lid closed to prevent the product from drying out and store upside down. Use a small amount of paint thin ner to soften. Avoid
heat, sparks, flame and other ignition sources.

T: 908.757.2323 ✛ F: 908.757.3439
AISALES@ARCHIRONDESIGN.COM ✛ ARCHIRONDESIGN.COM 327