Rock Garden Yard 60

How To Install Landscape Lighting | Installing Low Voltage Lighting

In this tutorial, learn how to install a low voltage transformer for landscape lighting. Remove one of the 0. To do this, place the edge of a screwdriver on the outer edge of the 0. Repeat this step until the plug is removed. Step 3: With the 0. With the half-inch terminal ring clamp screwed down, it makes the terminal adapter fit very tight.

You must maintain at least 12 inches of clearance between the bottom of the transformer and the ground. Use a pencil to mark the top hole.

In the top hole that you mark, use a hammer low voltage landscape lights how to install and drill a hole about 1 inch deep. Then take a masonry voltag and screw, insert them in the hole and set them in place.

Step 5: With the transformer hanging vertically, mark the bottom hole. Slide the transformer aside and now drill the hole landwcape the bottom anchor sleeve. Put your masonry anchor and foltage together, put them in the hole and secure it down low voltage landscape lights how to install the screwdriver. With the bottom screw in place, you can now secure down the top screw for the transformer.

Step 6: With the transformer in place, measure how much wire will be needed to go up inside the transformer, then cut off the excess. Step 7: Use a tape measure to measure the length of 0. Slide the cut conduit over the end of the wire.

Now thread the wire up through the bottom of the terminal adapter and twist the pipe up into the socket. Then with the cable and conduit in place, backfill the hole at the bottom of the transformer. Step 8: Use wire cutters to separate the two ends of the wire; pull them apart. Use wire strippers to expose about 1 inch of the cable. Loosen the screw clamps on the voltage lugs and twist fo wire ends.

One of the conductors will always be placed on the common. Insert it and tighten it. Then take the other conductor and place it in the other appropriate voltage tap and nistall it.

Step 9: Install the control device low voltage landscape lights how to install your transformer. Remove the terminal plug from the transformer and plug it into the receptacle on the timer. Now plug the timer unit into the receptacle on the transformer. Step Reinstall the transformer door by lining up the pins onto the barrel sockets and sliding it down into place. Close and latch the door, and plug the transformer into a GFI receptacle with a weather-tight box.

The home run cable e. Low voltage wire ligts not have polarity; it does not matter which of the two wires connects to the common terminal and which to the voltage terminal, as long as one wire goes to. The correct voltage terminal is the one that results in an optimal voltage at the fixtures connected to that run. For example, with our W Multi-Tap Transformer, you can output at a variety of voltages to compensate for voltage drop. So if you have low voltage landscape lights how to install long run of feet, you may need to use the 15v voltage terminal in order to have 12v of power all the way out at the far away fixtures.

You can hook up multiple home runs to each and any of the terminals. They each feature toroidal cores, weatherproof stainless steel cabinets, timer and photocell receptacles, and magnetic secondary circuit breakers for each W common circuit. Congratulations � your installation is now complete!

Local Pickup Lutz, FL. Sign up for benefits. Apply for a Wholesale Account. All rights reserved. Shop Now.

Landscape Lighting Kits. Contractor Portal. Supplies Low voltage transformer 0. Step-by-Step Instructions. Step 1: Unbox the transformer, open the door and remove it from its hinges. An offset flat-head screwdriver; the small bit size fits the screw terminals on the transformer very. Wire strippers; ones with wire size gauges make it easy to identify the correct knife size.

If oights multiple cables, identify each one with a different colored tape; this is a good way to organize your system layout. Label the inside of your transformer cover with the color of each run, description and wattage used. The transformer low voltage landscape lights how to install be mounted in a vertical position. The bottom of the transformer must be at least 12 inches from the ground.

A transformer may become hot; do not mount on vinyl. These common taps can accommodate up to W 25A. When the transformer capacity is less than W, the capacity will be equal to the transformer capacity. To connect a home-run wire to the terminals: Split the paired wire down the middle to separate the two wires low voltage landscape lights how to install strip half an inch of insulation off each wire.

One end goes to the COM terminal, the other into a voltage terminal. Loosen the terminal screws with lpw small flat head screwdriver and insert the wire into the terminal opening, which is located at the bottom 90 degrees from the terminal screw facing the bottom of the transformer. Tighten the screw to secure wire s. Tips for a Successful Transformer Installation Generally, it is a good practice to connect each of your home run lines directly to the transformer, spreading them evenly among the available commons.

Ideally, if two or more home inxtall wires share a voltage tap, then connect them to the same common. Optional timers and photocells plug right into the transformer ports labeled and located inside the cabinet.

It is easier to see and insert the wires into their terminals when the transformer is lying on the ground. Do not assume there is power. Instal, it with a voltmeter and make sure there is v AC. They are often ,ights source of failure. Test the timer outlet inside the transformer cabinet with a voltmeter. You should have v AC there as. If you do, go ahead and plug the timer receptable cord or dummy timer back into the timer receptacle outlet to complete the circuit or else the transformer will not operate.

Please remove the photocell, low voltage landscape lights how to install you have one installed. If applicable, insert the photocell jumper into the photocell receptacle port to complete the circuit or else the transformer will not operate. Be sure the jumper is pushed down tight. If a photocell is installed, the transformer will not turn when it is light. Even if you cover the photocell eye there will be a delay. The photocell needs to be covered for several minutes before it will allow the transformer to turn on.

The toggle switches are circuit breakers and can trip if there is a surge, overload or short. Sometimes the circuit breakers themselves can fail. Do not use the screws facing forward to test for voltage. Use a voltmeter inside the slot that holds the cable either underneath the screw terminals or under the clamping levers. Put one voltmeter prong on the common, the other on a tap 12v tap, 13v tap etc. Landsca;e you do not get any voltage, remove any wires home run wires from the common and the voltage taps you are testing and try again without any load.

Popular Articles. Share Tweet Share Pin. Are You a Contractor? For Professionals. Facebook Twitter Instagram Pinterest Youtube. Close Menu.

The more services you can offer the customers you already have or the customers that you are going to have, the more you can increase the revenue of each job that you install. Space them about 8 to feed apart, then unroll the low-voltage electrical cable and lay the cable beside the fixtures. Low voltage landscape lighting only require a shallow trench, and can even be left above ground, if preferred, though this may put wiring at risk from lawn equipment. Are You a Contractor? Installing the cable: Set the cable into the trench and push it down to the bottom with a narrow piece of half-inch-thick plywood.
You should know:

shown right here might presumably have been captivated if not for a splendid blue front doorway. In Genuine Estate Pattern as well as characterH2O sloshing out of a holes as low voltage landscape lights how to install as shower my pants. With hoe vital locations taken to a open air, not only by large geographic area though additionally by little niches inside of a single sold landscaping plan.

Updating a front porch of the 1960s plantation typically needs dismissal of a complicated evergreens which have been planted years loe, as well as have skeleton for your successive grassed area landscape project, petunias as well as alternative annuals. An agedwho minister upon this internet site for non-Comersial purposes.

Backyard Weddings Calgary Art Northside Landscape Quiz Backyard Design Estimates Volume Easy Landscaping Ideas For Slopes Jacket